Oldcastle-buildingenvelope Reliance StormMax High Performance Manuel d'utilisateur

Note: Installation and Glazing Manuals are product specific. FOR REVIEW ONLY!February

February 2014 08-Mullion-Reniforcing 1-866-Oldcastle (653-2278) www.oldcastlebe.com1.4 a. Insert RS-35 Reinforcement Steel into HW-500 Jamb or Mulli

February 2014 09-Horizontal-Fabrication 1-866-Oldcastle (653-2278) www.oldcastlebe.com1.5 a. Cut all Horizontal members as follows:

February 2014 10-Pressure-Plate-Fab 1-866-Oldcastle (653-2278) www.oldcastlebe.com1.6 a. Cut HW-163 Pressure Plate to D.L.O. minus 1/4" for hor

February 2014 11-Pressure-Plate-Fab 1-866-Oldcastle (653-2278) www.oldcastlebe.comFIGURE 1.6bGP-165 Gasket Notching1.6 con't e. Cut GP-165 Gaske

February 2014 12-Pressure-Plate-Fab 1-866-Oldcastle (653-2278) www.oldcastlebe.comInstall GP-165 gasket into HW-163 pressure platemaking sure that the

February 2014 13-Jamb-Mullion-Installation 1-866-Oldcastle (653-2278) www.oldcastlebe.com2.0 a. Insert "F" or"T" Anchor into the

February 2014 14-Horizontal-Installation 1-866-Oldcastle (653-2278) www.oldcastlebe.com2.1 a. Prior to attaching horizontal members follow sealant i

February 2014 15-Horizontal-Installation 1-866-Oldcastle (653-2278) www.oldcastlebe.comHORIZONTAL MEMBER INSTALLATION CONTINUEDAdequate sealant should

February 2014 16-Horiz Filler-Installation 1-866-Oldcastle (653-2278) www.oldcastlebe.comHORIZONTAL FILLER INSTALLATION2.2 a. Insert HW-737 Filler fr

February 2014 17-Perimeter-Seals 1-866-Oldcastle (653-2278) www.oldcastlebe.comOptional SealOptional sealHead seal is similar2.3 a. Position backer

February 2014 00-Table-of-Contents 1-866-Oldcastle (653-2278) www.oldcastlebe.comGeneral Information Product Use

February 2014 18-Zone-Plug-Installation 1-866-Oldcastle (653-2278) www.oldcastlebe.comHW-355 zone plugForce sealantinto gasket raceSeal along tongue o

October 2013 19-Isolator-Installation 1-866-Oldcastle (653-2278) www.oldcastlebe.comISOLATOR GASKET INSTALLATION3.0 a. Install face gaskets into all p

February 2014 20-Isolator-Install-Dry-Glaze 1-866-Oldcastle (653-2278) www.oldcastlebe.comDRY GLAZED GASKET INSTALLATION (OPTIONAL)3.1 a. Cut vertic

February 2014 21-Glass-Sizing 1-866-Oldcastle (653-2278) www.oldcastlebe.comGLASS SIZING AND INSTALLATION3.2 a. Set glass in opening. Ensure that

February 2014 22-Pressure-Plate-Seals 1-866-Oldcastle (653-2278) www.oldcastlebe.com3.3 Repeat steps 3.2 until all glass is set, working row by row

February 2014 23-Pressure-Plate-Splice 1-866-Oldcastle (653-2278) www.oldcastlebe.comPRESSURE PLATE SPLICE INSTRUCTIONSQuarter pointsQuarter points1/4

February 2014 24-Top-of-Mull-Seal 1-866-Oldcastle (653-2278) www.oldcastlebe.com3.5 a. After all pressure plates are installed on the frame, torque

February 2014 25-Horizontal-Weep-Holes 1-866-Oldcastle (653-2278) www.oldcastlebe.comHW-163 cut length =D.L.O. minus 1/4"5/16" dia. weep hol

February 2014 26-Interior-Seals-Wet-Glazed 1-866-Oldcastle (653-2278) www.oldcastlebe.com3.6 a. Clean all silicone surfaces and joints with 50% isop

February 2014 27-Door-Installation 1-866-Oldcastle (653-2278) www.oldcastlebe.com3.7 All door framing components are shipped fabricated from the facto

February 2014 01-General-Info 1-866-Oldcastle (653-2278) www.oldcastlebe.comPRODUCT USEThe StormMax Reliance curtain wall system is intended for insta

February 2014 28-Parts-List 1-866-Oldcastle (653-2278) www.oldcastlebe.comMullions / Horizontals / FillersMiscellaneous Parts ListAccessories ListFast

February 2014 02-General-Info 1-866-Oldcastle (653-2278) www.oldcastlebe.comPROTECTION AND STORAGEHandle all material carefully. Do not drop from the

February 2014 03-Cut-Material 1-866-Oldcastle (653-2278) www.oldcastlebe.comFRAME FABRICATION1.0 Unless otherwise noted, the details shown in these in

February 2014 04-Material-Fab-Guide 1-866-Oldcastle (653-2278) www.oldcastlebe.comtyp.Quarter pointsD.L.O. minus 1/16"Roll-Over HorizontalD.L.O.T

February 2014 05-Shear-Block-Holes 1-866-Oldcastle (653-2278) www.oldcastlebe.com3/4"2 1/2"#11 (.191 dia.)holes for#14 fastenersJAMBS WITH&q

February 2014 06-Jamb-Fabrication 1-866-Oldcastle (653-2278) www.oldcastlebe.comHW-202-01 Anchor SleeveHW-710 Jamb MullionHW-185-01Shear Block(4) FS-9

February 2014 07-Mullion-Fabrication 1-866-Oldcastle (653-2278) www.oldcastlebe.comFIGURE 1.31.3 a. Prior to HW-185-01 Shear Block attachment insert